Code Reader 1200 Instalační manuál Strana 143
- Strana / 176
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
PARAMETER REFERENCES
131
5
ACK Character
This setting specifies an ASCII character to be used as the ACK character. Selections: a
character from NUL (0x00) to DEL (0x7F).
NOTE
The ACK Character must be different from the NAK Character and must not
contain reserved characters (see Appendix D). Setting to previously defin
ed
characters such as XON, XOFF, or host commands conflicts with normal
operation of these characters. 8-bit data is not recognized when the option
Data Bits has been set as 7 Data Bits.
To set this feature:
1. Determine the desired character.
2. Use the Chart in Appendix C to find the hex equivalent
for the desired character.
3. Go to page 48 and scan the ENTER/EX
IT PROGRAMMING MODE to enter
Programming Mode.
4. Scan the barcode: SELECT ACK CHARACTER.
5. Scan the two hex equivalent characters
from the keypad in Appendix B that represent the
desired character in step 1 above.
6. Scan the ENTER/EXIT PROGRAMMING MODE barcode to exit Programming Mode.
This completes the procedure.
NAK Character
This setting specifies an ASCII character to be used as the NAK character. Selections: a
character from NUL (0x00) to DEL (0x7F).
NOTE
The ACK Character must be different from the NAK Character and must not
contain reserved characters (see Appendix D). Setting to previously defin
ed
characters such as XON, XOFF, or host commands conflicts with normal
operation of these characters. 8-bit data is not recognized when the option
Data Bits has been set as 7 Data Bits.
To set this feature:
1. Determine the desired character.
2. Use the Chart in Appendix C to find the hex equivalent
for the desired character.
3. Go to page 49 and scan the ENT
ER/EXIT PROGRAMMING MODE barcode to enter
Programming Mode.
4. Scan the barcode: SELECT NAK CHARACTER.
5. Scan the two hex equivalent characters
from the keypad in Appendix B that represent the
desired character in step 1 above.
6. Scan the ENTER/EXIT PROGRAMMING MODE barcode to exit Programming Mode.
This completes the procedure.
- Reference Manual 1
- CONTENTS 3
- REFERENCES 9
- FCC COMPLIANCE 10
- POWER SUPPLY 10
- CE COMPLIANCE 10
- HANDLING 11
- 1 INTRODUCTION 13
- 1.3 AVAILABLE MODELS 14
- 1.4 ACCESSORIES 15
- 2 INSTALLATION 16
- INSTALLATION 17
- 2.1.4 Electrical Connections 20
- RS232 Interface 21
- Outputs 23
- 2.2 TC1200 CCD SCAN ENGINE 24
- 2.2.2 Electrical Connections 25
- USB Interface 26
- TC1200 EXTERNAL TRIGGER 27
- OUT1/2 28
- 2.3 POSITIONING 29
- 3.1 TC1200 CONFIGURATION 34
- RS232 Models 34
- USB Models 34
- Command Syntax 35
- 4 BARCODE CONFIGURATION 52
- ËÄ$P,HA00,PmÂÎ 52
- ËÄ$P,HA05,PmHÎ 52
- ËÄ$P,HA47,PmtÎ 53
- ËÄ$P,HA35,Pm]Î 53
- ËÄ$P,HA2B,PmWÎ 53
- ËÄ$P,HA2C,Pm_Î 53
- GLOBAL INTERFACE FEATURES 55
- AUD RATE 56
- ATA BITS 56
- TOP BITS 56
- BAUD RATE 57
- DATA BITS 58
- STOP BITS 58
- RS232/USB-COM 59
- INTERCHARACTER DELAY 60
- DISABLE CHARACTER 60
- ENABLE CHARACTER 60
- ACK/NAK OPTIONS 60
- ACK CHARACTER 60
- NAK CHARACTER 61
- ACK/NAK TIMEOUT 61
- ACK/NAK RETRY COUNT 61
- ACK/NAK ERROR HANDLING 61
- USB-KBD 62
- KEYBOARD COUNTRY 63
- KEYBOARD COUNTRY (CONTINUED) 64
- KEYBOARD INTERCODE DELAY 64
- SEND CONTROL CHARACTERS 65
- USB KEYBOARD SPEED 65
- KEYBOARD SPEED (CONTINUED) 66
- ËÄ$CKBSP09mRÎ 66
- ËÄ$CKBSP0Am3Î 66
- READING PARAMETERS 67
- ILLUMINATION MODE 68
- OPERATING MODE 68
- AUTOMATIC THRESHOLD 68
- PHASE OFF EVENT 69
- TIMEOUT 69
- SERIAL START 69
- SERIAL STOP 69
- LED INDICATION 69
- LABEL PROGRAMMING MODE 70
- EXPOSURE MODE 70
- READING CONDITIONS 70
- DATA FORMAT 71
- DATA TRANSMISSION 72
- CODE VERIFIER MODE 72
- MATCH STRING 72
- WRONG CODE STRING 72
- CASE CONVERSION 73
- GLOBAL PREFIX 73
- GLOBAL SUFFIX 73
- NO READ STRING 73
- TRANSMIT AIM IDS 74
- TRANSMIT CUSTOM LABEL IDS 74
- CUSTOM LABEL IDENTIFIERS 74
- Enter/Exit Configuration 75
- Enter/Exit Configuration 76
- DIGITAL OUTPUTS 78
- OUTPUT 1 ACTIVATION EVENT 79
- OUTPUT 1 DEACTIVATION EVENT 79
- OUTPUT 2 ACTIVATION EVENT 80
- OUTPUT 2 DEACTIVATION EVENT 80
- POWER SAVE 81
- SLEEP MODE TIMEOUT 82
- CODE SELECTION 83
- CHECK CHARACTER TX 85
- EXPAND TO EAN-13 85
- NUMBER SYSTEM TX 85
- UPC-A MINIMUM READS 86
- EXPAND TO UPC-A 87
- UPC-E MINIMUM READS 88
- ISBN CONVERSION 89
- ISSN CONVERSION 89
- FLAG 1 CHARACTER 90
- EAN-13 MINIMUM READS 90
- EAN-8 MINIMUM READS 91
- ENABLE OPTIONAL P2 ADD-ON 92
- ENABLE OPTIONAL P5 ADD-ON 92
- P2 MINIMUM READS 92
- P5 MINIMUM READS 93
- OPTIONAL ADD-ON TIMER 93
- GTIN FORMAT 94
- IN-STORE MINIMUM READS 95
- CODE 39 95
- CODE 39 FULL ASCII 95
- CODE 39 CHECK TX 96
- CODE 39 START/STOP TX 96
- CODE 32 CHECK TX 97
- CODE 32 START/STOP TX 97
- Code 39 Check Options 98
- Code 39 Decoding Options 98
- QUIET ZONES 100
- STITCHING 100
- SET LENGTH 101
- CODE 128 101
- GS1-128 ENABLE 101
- CODE LENGTH CONTROL 101
- EXPAND TO CODE 39 102
- Code 128 Check Options 102
- CHECK TX 102
- FUNCTION CHARACTER TX 102
- SUB-CODE CHANGE TX 102
- Code 128 Decoding Options 103
- MINIMUM READS 103
- DECODING LEVEL 103
- CHARACTER CORRELATION 104
- ISBT 128 CONCATENATION 105
- CONCATENATION MODE 105
- INTERLEAVED 2 OF 5 106
- CHECK CALCULATION 107
- ZERO PATTERN 109
- STANDARD 2 OF 5 110
- INDUSTRIAL 2 OF 5 113
- CODABAR 116
- CODABAR ABC 117
- Codabar Check Options 118
- START/STOP SET 118
- START/STOP TX 119
- START/STOP MATCH 119
- Codabar Decoding Options 119
- INTERDIGIT RATIO 120
- CODE 11 122
- Code 11 Check Options 123
- Code 11 Decoding Options 124
- GS1 DATABAR OMNIDIRECTIONAL 126
- GS1 DATABAR EXPANDED 127
- COUPON CONTROL 128
- GS1 DATABAR LIMITED 129
- CODE 93 130
- Code 93 Check Options 131
- Code 93 Decoding Options 132
- MSI Check Options 135
- MSI Decoding Options 136
- PLESSEY 137
- Plessey Check Options 138
- Plessey Decoding Options 138
- 5 PARAMETER REFERENCES 140
- Intercharacter Delay 141
- Disable Character 141
- Enable Character 142
- ACK NAK Options 142
- ACK Character 143
- NAK Character 143
- ACK NAK Timeout Value 144
- ACK NAK Retry Count 144
- Keyboard Intercode Delay 145
- 5.2 READING PARAMETERS 145
- 5.2.1 Illumination Mode 145
- Illumination Mode 145
- 5.2.2 Operating Mode 146
- Operating Mode 146
- Automatic Threshold 146
- Phase Off Event 147
- Timeout 147
- Serial Start 148
- Serial Stop 148
- 5.2.3 Good Read LED 149
- LED Indication 149
- 5.2.4 Exposure Mode 149
- 5.2.5 Preset Recipes 149
- Reading Conditions 149
- 5.3 DATA FORMATTING 150
- 5.3.1 Global Prefix/Suffix 151
- No Read String 152
- 5.3.2 Code Identifiers 153
- Label IDs 153
- Label ID: Pre-loaded Set 153
- TC1200 REFERENCE MANUAL 154
- Global AIM ID 155
- 5.3.3 Code Verifier 156
- Match String 156
- Wrong Code String 156
- 5.4 DIGITAL OUTPUTS 157
- Activation Event 157
- Deactivation Event 157
- Deactivation Timeout 157
- Active Level 157
- 5.5 POWER SAVE 158
- Sleep Mode Timeout 158
- 5.6 CODE SELECTION 158
- Decoding Level 158
- Interdigit Ratio 159
- Character Correlation 159
- Minimum Reads 159
- Stitching 160
- Quiet Zones 160
- 5.6.1 Concatenation 160
- Concatenation Mode 160
- 5.6.2 Set Length 161
- Set Length 1 161
- Set Length 2 162
- 6 MAINTENANCE 163
- 7 TECHNICAL FEATURES 164
- 7.1 READING DIAGRAMS 165
- A DEFAULT PARAMETERS TABLE 166
- Transmit Labels in 168
- GS1-128 Data Format) 168
- C ASCII/HEX/DECIMAL CHART 172
- ASCII CHART 173
- D RESERVED CHARACTERS 174
- DECLARATION OF CONFORMITY 175
Související produkty a manuály pro Čtečky čárových kódů Code Reader 1200
Tripp Lite SUPT60K Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Werkzeug Tripp Lite SUPT60K.
Wir stellen 1 PDF-Handbücher Tripp Lite SUPT60K zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Tripp lite SUPT60K Bedienungsanleitung (2 Seiten)
Marke: Tripp-lite | Kategorie: Tools | Größe: 0.12 MB |
Inhaltsverzeichnis
Weitere Produkte und Handbücher für Werkzeug Tripp Lite
| Modelle | Dokumententyp |
|---|---|
| BP240V99 |
Bedienungsanleitung
Tripp Lite BP240V99 User Manual,
2 Seiten
|
| INTERNET525U ES |
Bedienungsanleitung
 
Tripp Lite INTERNET525U ES User Manual,
3 Seiten
|
| BP24V28-2U |
Bedienungsanleitung
Tripp Lite BP24V28-2U User Manual [en] [fr] ,
3 Seiten
|
| BP72V28-3UNAFTA |
Bedienungsanleitung
Tripp Lite BP72V28-3UNAFTA User Manual [en] [ru] [de] [es] [fr] [it] ,
2 Seiten
|
| External Battery Pack BP72V28RT-3U |
Bedienungsanleitung
Tripp Lite External Battery Pack BP72V28RT-3U User Manual,
2 Seiten
|
| 93-2120_ES |
Bedienungsanleitung
Tripp Lite 93-2120_ES User Manual,
3 Seiten
|
| HCRK-1 |
Bedienungsanleitung
Tripp Lite HCRK-1 User Manual,
12 Seiten
|
| P005-006 |
Bedienungsanleitung
Tripp Lite P005-006 User Manual,
2 Seiten
|
| INTERNET350U |
Bedienungsanleitung
Tripp Lite INTERNET350U User Manual [en] ,
2 Seiten
|
| APINT Series |
Bedienungsanleitung
Tripp Lite APINT Series User Manual,
44 Seiten
|
| OmniSmart OMNI300NAFTA |
Bedienungsanleitung
Tripp Lite OmniSmart OMNI300NAFTA User Manual,
1 Seiten
|
| BP48V60-3UNAFTA |
Bedienungsanleitung
Tripp Lite BP48V60-3UNAFTA User Manual,
3 Seiten
|
| P047-006 |
Bedienungsanleitung
Tripp Lite P047-006 User Manual,
2 Seiten
|
| 2U Tower Stand |
Bedienungsanleitung
Tripp Lite 2U Tower Stand User Manual,
1 Seiten
|
| HTR05-1U |
Bedienungsanleitung
Tripp Lite HTR05-1U User Manual,
1 Seiten
|
| TE Series |
Bedienungsanleitung
Tripp Lite TE Series User Manual,
20 Seiten
|
| Alternative Power Sources |
Bedienungsanleitung
Tripp Lite Alternative Power Sources User Manual,
36 Seiten
|
| AVR550U |
Bedienungsanleitung
Tripp Lite AVR550U User Manual,
1 Seiten
|
| BP36V15-2U |
Bedienungsanleitung
Tripp Lite BP36V15-2U User Manual,
2 Seiten
|
| Omnismart OMNIVS500U |
Bedienungsanleitung
Tripp Lite Omnismart OMNIVS500U User Manual,
2 Seiten
|
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce