Code Reader™ 2300 (CR2300)
Included with the CR2300
Quickstart Guide
CR2321
Depending on the kit purchased, a combinaon of the following components will be included with
your reader:
Charging Staon with
or without
an Embedded
CodeXML® Modem
USB
Cable
Power
Supply
CodeXML®
M3 Modem
with RS232 or
USB Cable
Baery
Cartridge
C008663_01_CR2300_QuickStart_Guide
Weighted
Base Plate
Screws and
Rubber Feet
Charging Station Assembly Instructions
1. Plug the barrel side of the USB charge cable or power supply (depending on which you
ordered) into the charger. (Figure 1)
2. (Oponal) To aach the weighted base, place the ‘This Side Down’ (Figure 2) side of the
weighted base onto the surface, place the Charging Staon on top of it (Figure 3) and secure
with the screws provided. (Figure 3)
Figure 1
Figure 2
Figure 3
3. Rubber feet can be placed on the corners of the weighted base (Figure 4) or directly onto the
Charging Staon (Figure 5) to prevent slipping from a surface.
When the CR2300 is in batch mode, the storage icon (Figure 15) will remain solid to indicate data
has been stored. The storage icon will ash every 10 seconds to indicate data is stored when in
sleep mode.
If the storage memory is full, the storage icon will ash 5 mes every second. Data will need to be
downloaded or deleted to free up memory space. Note, the storage icon will not ash if there is
no data stored.
To put the CR2300 into Batch Mode, please reference the CR2300 Conguraon Guide located at
www.codecorp.com.
Batch Mode
Establishing a Bluetooth® Connection
1. If establishing a Bluetooth connecon using the Charging Staon with embedded CodeXML®
Modem, slide the Communicaon Mode Switch on the boom of the Charger/Modem
Staon to Bluetooth mode (the direcon of the arrow). For USB communicaon mode
informaon, please reference the CR2300 User Manual located at www.codecorp.com.
2. Scan the QuickConnect Code located on the front of the Charger/Modem Staon or on the
external CodeXML® M3 Modem. (Figures 13 and 14).
3. The wireless icon located at the top of the reader will ash as it aempts to make connecon.
(Figure 15) The blue LED on the Charging Staon (or CodeXML® M3 Modem) will also ash as
it aempts to connect and will turn solid when the connecon is established. The CR2300 will
beep once and the wireless icon will ash every 10 seconds. (Figures 13, 14 and 15)
For addional CodeXML® M3 Modem informaon, please reference the CodeXML® M3 Modem
QuickStart Guide.
Figure 15
Blue
LED
Blue
LED
Wireless Icon Storage Icon
Good Read
Indicator
QuickConnect
Code
Figure 13
Figure 14
Important Note If Using a non-Code Bluetooth Device:
To connect to a Bluetooth device not manufactured by Code, you will need the Bluetooth address
(oen referred to as the BD_ADDR) of that device. The 12-character Bluetooth address can be
found on the device near the serial number. Then visit Code’s web site at:
hp://www.codecorp.com/bdaddr.php and enter the 12-character address to create the
QuickConnect Code.
You will need to locate the Communicaons (COM) Port assigned to the Bluetooth serial port
protocol before installing the Bluetooth Conguraon Manager soware that is included with your
Bluetooth adapter (e.g., COM 10). This is the COM Port through which the CR2300 will connect.
© 2013 Code Corporaon. All rights reserved.
(62 stránky)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce